Industry Insight November 12, 2026

How to Calculate AHU Size and CFM for Your Building

How to Calculate AHU Size and CFM for Your Building

Picking the wrong air handling unit (AHU) is one of the costliest HVAC mistakes. An undersized unit leaves rooms warm and stuffy. An oversized one short-cycles, wastes energy and fails to control humidity. Sizing starts with two numbers: the airflow your building needs in CFM (cubic feet per minute) and the cooling capacity in tons of refrigeration (TR). This guide shows how to calculate both, with a worked example.

Quick answer: To size an AHU, calculate the building’s sensible cooling load in BTU/hr, then divide by (1.08 × supply air temperature difference in °F) to get CFM. Add a 10% margin, check the result against ventilation and air-change requirements, and select an AHU whose rated airflow and coil capacity cover the highest value.

What Is an AHU, and Why Does Sizing Matter?

An Air handling unit is the central equipment that conditions and circulates air through ducts. It houses the fan, cooling and heating coils, filters and often a damper section for fresh air. Its two key ratings are airflow (CFM or CMH) and coil capacity (TR or kW).

Correct sizing affects:

  • Comfort: even temperatures and controlled humidity
  • Energy cost: fans and chillers running near their efficient range
  • Equipment life: fewer on/off cycles and less coil freezing
  • Indoor air quality: enough filtered fresh air for occupants

Step 1: Calculate the Building’s Cooling Load

CFM depends on load, so start there. Your cooling load is the heat that must be removed each hour, from:

  • Envelope gains: walls, roof and glass (solar heat through windows is often the largest)
  • Occupants: about 250 BTU/hr sensible plus latent heat per person in office settings
  • Lighting and equipment: computers, servers, machinery
  • Fresh air: outdoor air brought in is hot and humid

For a quick estimate, one TR equals 12,000 BTU/hr, and many commercial spaces need roughly 1 TR per 100–200 sq ft depending on climate, glazing and occupancy. Use this only for early planning. For final selection, run a proper load calculation using ASHRAE methods or software such as HAP or Trace, or have a qualified HVAC engineer do it.

Step 2: Use the CFM Formula

Once you know the sensible load, calculate airflow:

CFM = Sensible Load (BTU/hr) ÷ (1.08 × ΔT)

ΔT is the difference between room temperature and supply air temperature. For comfort cooling it is typically 18–22°F (about 10–12°C).

Metric version: Airflow (m³/s) = Sensible Load (kW) ÷ (1.21 × ΔT in °C). Multiply m³/s by 3,600 for CMH. To convert, 1 CFM ≈ 1.7 CMH.

Rule of thumb: 350–450 CFM per TR is common for comfort cooling. Treat it as a sanity check, not a design basis.

Step 3: Check Fresh Air Requirements

Your AHU must also deliver enough outdoor air. ASHRAE 62.1 calculates this per zone:

Outdoor air = (Rp × people) + (Ra × floor area)

For offices, Rp is about 5 CFM per person and Ra about 0.06 CFM per sq ft. In India, also refer to the National Building Code (NBC 2016) and ISHRAE guidelines. Local codes may require more.

Step 4: Check Air Changes per Hour (ACH)

Some spaces are sized by air changes rather than load. The formula is:

CFM = (ACH × Room Volume in cubic feet) ÷ 60

Space typeTypical ACH
General offices4–8
Retail6–10
Commercial kitchens15–30+
Operating theatres20+

Always use the highest CFM from the load, ventilation and ACH calculations.

Worked Example: 5,000 sq ft Office

Given: 5,000 sq ft office, 10 ft ceiling, 100 occupants, total cooling load of 240,000 BTU/hr (20 TR), sensible heat ratio of 0.75, supply ΔT of 20°F.

  1. Sensible load: 240,000 × 0.75 = 180,000 BTU/hr
  2. Load-based CFM: 180,000 ÷ (1.08 × 20) = 8,333 CFM (about 417 CFM/TR)
  3. Fresh air: (5 × 100) + (0.06 × 5,000) = 800 CFM, roughly 10% of supply
  4. ACH check: volume is 50,000 cu ft, so 8,333 × 60 ÷ 50,000 = 10 ACH, comfortably above the 4–8 office range
  5. Add 10% margin: 8,333 × 1.1 ≈ 9,200 CFM
  6. In metric: 9,200 CFM ≈ 15,600 CMH

You would select a 20 TR AHU rated around 9,000–10,000 CFM.

Step 5: Select the AHU Size

With CFM and TR confirmed, finalize the unit:

  • Match airflow and coil capacity. The unit should deliver your CFM at the required external static pressure, not just at free air.
  • Check coil face velocity. Keep it near 450–500 fpm to avoid moisture carry-over. Coil face area = CFM ÷ face velocity. At 9,200 CFM and 500 fpm, you need about 18.4 sq ft.
  • Calculate static pressure. Add duct losses, filters, coils and dampers. The fan must meet this total.
  • Include fresh air and filtration. Confirm the mixing box and filter grade (MERV 13 or higher is common for offices).
  • Plan for the future. If expansion is likely, consider VFD fans rather than a much larger unit.

Common AHU Sizing Mistakes

  • Using area-only rules of thumb: these ignore glazing, orientation and occupancy.
  • Oversizing “to be safe”: this causes humidity problems and higher costs.
  • Ignoring latent load: humid climates need moisture removal, not just cooler air.
  • Forgetting static pressure: a fan that is perfect on paper underdelivers in real ducts.
  • Skipping the ventilation check: a unit that cools well can still fail air quality requirements.

Frequently Asked Questions

How do I calculate CFM for an AHU?
Divide the sensible cooling load in BTU/hr by 1.08 times the supply air temperature difference in °F.

What is the full form of BTU ?
 BTU (British Thermal Unit) is a standard unit of measurement for thermal energy. In HVAC (Heating, Ventilation, and Air Conditioning), it measures the amount of heat an air conditioner removes or a furnace adds from a space per hour

How many CFM per ton does an AHU need?
Comfort cooling typically needs 350–450 CFM per ton. Humid climates or low-ΔT designs may need more.

How do I convert CFM to CMH?
Multiply CFM by 1.699. For example, 1,000 CFM is about 1,700 CMH.

Can I size an AHU by square footage alone?
Only for rough budgeting. Final sizing needs a heat load calculation covering glazing, occupancy, equipment and fresh air.

What happens if the AHU is oversized?
The unit cycles too often, controls humidity poorly, uses more energy and wears out faster.

How much fresh air does an AHU need?
ASHRAE 62.1 sets it by occupancy and floor area. For offices, that is about 5 CFM per person plus 0.06 CFM per sq ft.

Conclusion

Sizing an AHU comes down to a sequence: calculate the load, convert it to CFM, verify ventilation and air changes, then select a unit that meets your airflow, coil capacity and static pressure needs. For large or critical buildings, have a qualified HVAC engineer validate your numbers before purchase.

Need help sizing an AHU? Contact our engineering team for a free load review.

A
AirTree Editorial
HVAC & Engineering Experts

Stay ahead with more industry insights

Join our newsletter to receive the latest HVAC technologies and ventilation solutions directly in your inbox.

Download Our Brochure

Fill in your details to get instant access to our product catalog

+91